收藏本站
CAV4201
Table 6. PIN DESCRIPTION
Pin
1
2
3
4
5
Pin Function
Name
CTRL
GND
RSET
SW
VBAT
Function
Enable and analog dimming control input pin.
Ground reference.
RSET pin. A resistor connected between the pin and ground sets the average LED current.
Interface to the inductor.
Supply voltage for the device.
VBAT is the supply input to the device. Typical current
conduction into this pin is less than 1 mA and voltage
transients of up to 40 V can be applied. To ensure accurate
LED current regulation, the VBAT voltage should be 3 V
higher than the total forward voltage of the LED string. A
bypass capacitor of 4.7 m F or larger is recommended
between VBAT and GND.
CTRL is the enable and analog dimming control input. An
internal pull ? down current of 20 m A allows the LEDs to
shutdown if CTRL is left floating. Voltages of up to 40 V can
be safely handled by the CTRL input pin.
When the CTRL voltage is less than 0.9 V (typ), the LEDs
will shutdown to zero current. When the CTRL voltage is
greater than about 2.6 V, the device is enabled and full scale
brightness is applied to the LED output. At voltages of less
than around 2.6 V, the LED current is progressively dimmed
until shutdown.
For lamp replacement applications, or applications where
operation in dropout mode is expected, it is recommended
that the CTRL pin voltage be derived from the LED cathode
terminal.
GND is the ground reference pin. This pin should be
connected directly to the ground plane on the PCB.
SW pin is the drain terminal of the internal low resistance
high ? voltage power MOSFET. The inductor and the
Schottky diode anode should be connected to the SW pin.
Voltages of up to 40 V can be safely handled on the SW pin.
Traces going to the SW pin should be as short as possible
with minimum loop area. The device can handle safely
“open ? LED” or “shorted ? LED” fault conditions.
RSET pin is regulated at 1.2 V. A resistor connected
between the RSET pin and ground sets the LED full ? scale
brightness current. The external resistance value and the
CTRL pin voltage determine the LED current during analog
dimming. The RSET pin must not be left floating. The
highest recommended resistor value between RSET and
ground is 90 k W .
http://onsemi.com
7
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CB-1377 PANEL ALUMINUM CHASSIS
CBC5300-24C ENERCHIP EH CBC5300 MODULE
CC-ACC-MX51-ETM ADAPTER TRACE ETM/ETB JTAG
CDBMCU-DEBUG EVAL BD FOR DSP CS48X & CS49X
CEL2MUSB E2GO CELL PHONE CHARGER USB
CH-14403 RACK SMALL MNT CHASSIS ALUMINUM
CH15MNP4 BATT CHARGER 15MINUTE W/4AA
CHCARCP BATT CHARGER CAR/HOME W/4AA CELL
相关代理商/技术参数
CAV424 制造商:未知厂家 制造商全称:未知厂家 功能描述:Converter IC for Capacitive Signals
CAV444 制造商:AD 制造商全称:Analog Devices 功能描述:C/V transmitter IC with adjustable output voltage for capacitive input signals
CAV-5.0-1.0 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes
CAV-5.0-1.5 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes
CAV-5.0-10 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes
CAV-5.5-6.8 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes
CAV-5.7-0.10 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes
CAV-5.8-2.2 制造商:TALEMA 制造商全称:TALEMA 功能描述:Common Mode Toroidal Chokes